:
from
to
Clear all
Access Power Controller w/ Power Supply/Chargers, 16 PTC Class 2 Relay Outputs, Dual 12/24VDC P/S...

        Access Power Controller w/ Power Supply/Chargers, 16 PTC Class 2 Relay Outputs, Dual 12/24VDC P/S @ 6A each, 115VAC, 2U

        SKU: MAXIMAL33RD1
        Altronix
        SKU: MAXIMAL33RD1
        Access Power Controller w/ Power Supply/Chargers, 16 PTC Relay Outputs, Dual 12/24VDC P/S @ 6A each, 115VAC, 2U

        Maximal33RD rack mount access power controller distributes and switches power to access control systems and accessories. It converts a 115VAC 50/60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC PTC protected outputs. Outputs are activated by an normally open (NO) or normally closed (NC) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. This unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the outputs.

        • Input
          • 115VAC 60Hz., 3.8A.
          • Normally closed [NC] or normally open [NO] dry contact inputs (switch selectable).
        • Outputs
          • 12VDC or 24VDC @ 12A total output current.
            • Power supply 1 / (8) outputs:
              • 12VDC @ 6A or 24VDC @ 6A.
            • Power supply 2 / (8) outputs:
              • 12VDC @ 6A or 24VDC @ 6A.
          • Sixteen (16) PTC protected outputs (auto-resettable).
          • Maximum current per ACM8R-M output is 2A.
          • Individually selectable Mag Lock/Strike (Fail-Safe, Fail-Secure) solid state fuse protected outputs.
          • Thermal and short circuit protection with auto reset.
        • Fire Alarm Interface
          • Latching or Non-Latching fire alarm reset switch individually selectable for each output.
          • Remote reset capability for latching Fire Alarm Interface mode.
            • Fire Alarm disconnect input options:
              • a) Normally open [NO] or normally closed [NC] dry contact input.
              • b) Polarity reversal input from FACP signaling circuit.
        • Visual Indicators
          • Individual Output Status LEDs located on the front panel.
        • Battery Backup
          • Built-in charger for sealed lead acid or gel type batteries (if batteries are required install separate enclosure).
          • Automatic switch over to stand-by battery when AC fails.
          • Zero voltage drop when unit switches over to battery backup (AC failure condition).
        • Supervision
          • AC fail supervision (form "C" contacts).
          • Notification trigger is selectable for 30 seconds (factory set) or 6 hours.
          • Low battery and battery presence supervision (form "C" contact).
        • Additional Features
          • Removable terminal blocks with locking screw flange.
          • 3-wire line cord.
          • Illuminated master power disconnect circuit breaker with manual reset.
        • Electrical
            • Temperature:
              • Operating: 0° C to 49° C (32° F to 120° F).
              • Storage: - 20° C to 70° C ( - 4° F to 158° F).
          • Relative Humidity 85% +/- 5%.
            • BTU/Hr (approx.):
              • 12VDC: 74 BTU/Hr.
              • 24VDC: 141 BTU/Hr.
              • 12VDC and 24VDC: 106 BTU/Hr.
          • System AC input VA requirement: 437VA.
          • 2% less
          Market price:$910.70 save $19.00
        • $891.70
         
        OR
        Access Power Controller w/ Power Supply/Chargers, 16 PTC Relay Outputs, Dual 12/24VDC P/S @ 6A each, 115VAC, 2U

        Maximal33RD rack mount access power controller distributes and switches power to access control systems and accessories. It converts a 115VAC 50/60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC PTC protected outputs. Outputs are activated by an normally open (NO) or normally closed (NC) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. This unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the outputs.

        • Input
          • 115VAC 60Hz., 3.8A.
          • Normally closed [NC] or normally open [NO] dry contact inputs (switch selectable).
        • Outputs
          • 12VDC or 24VDC @ 12A total output current.
            • Power supply 1 / (8) outputs:
              • 12VDC @ 6A or 24VDC @ 6A.
            • Power supply 2 / (8) outputs:
              • 12VDC @ 6A or 24VDC @ 6A.
          • Sixteen (16) PTC protected outputs (auto-resettable).
          • Maximum current per ACM8R-M output is 2A.
          • Individually selectable Mag Lock/Strike (Fail-Safe, Fail-Secure) solid state fuse protected outputs.
          • Thermal and short circuit protection with auto reset.
        • Fire Alarm Interface
          • Latching or Non-Latching fire alarm reset switch individually selectable for each output.
          • Remote reset capability for latching Fire Alarm Interface mode.
            • Fire Alarm disconnect input options:
              • a) Normally open [NO] or normally closed [NC] dry contact input.
              • b) Polarity reversal input from FACP signaling circuit.
        • Visual Indicators
          • Individual Output Status LEDs located on the front panel.
        • Battery Backup
          • Built-in charger for sealed lead acid or gel type batteries (if batteries are required install separate enclosure).
          • Automatic switch over to stand-by battery when AC fails.
          • Zero voltage drop when unit switches over to battery backup (AC failure condition).
        • Supervision
          • AC fail supervision (form "C" contacts).
          • Notification trigger is selectable for 30 seconds (factory set) or 6 hours.
          • Low battery and battery presence supervision (form "C" contact).
        • Additional Features
          • Removable terminal blocks with locking screw flange.
          • 3-wire line cord.
          • Illuminated master power disconnect circuit breaker with manual reset.
        • Electrical
            • Temperature:
              • Operating: 0° C to 49° C (32° F to 120° F).
              • Storage: - 20° C to 70° C ( - 4° F to 158° F).
          • Relative Humidity 85% +/- 5%.
            • BTU/Hr (approx.):
              • 12VDC: 74 BTU/Hr.
              • 24VDC: 141 BTU/Hr.
              • 12VDC and 24VDC: 106 BTU/Hr.
          • System AC input VA requirement: 437VA.
          • SKU
            MAXIMAL33RD1
        • Manufacturer
          Altronix

        Product questions

        No questions yet. Be the first to ask the question!

        Guarantee SealOur Commitment
        The mission of WorldEyeCam, Inc.is to provide consumers with the most up to date security products at the best prices available on the market today. As security is advancing at such a rapid rate we try to exceed our customers expectations by providing unparallel customers service and technical support. We strive to stay on the forefront of the most up to date products and news in regards to our industry. Our website www.Worldeyecam.com contains a broad spectrum of surveillance products as well as industry information. Our website is updated daily as we make our way through this technological wave of security products. Our goal and focus is to stay on top of the latest innovations in technology and securities and to remain a trusted industry leader for years to come.

        WorldEyeCam  is a CCTV products distribution and integration company located in Southern California in the heart of Orange County. We operate out of a 14,000 sq.ft warehouse & a separate product demo show room. We proudly offer 1st class technical support for our customers we serve with the complete understanding that it is you, the customer that matters to every successful business. If you haven't already learned the hard way, you will understand that it takes more than just a website and the ability to sell a product - anyone can sell a product! But, it takes commitment to offerDEPENDABLE AND CONSISTENT technical support & customer SERVICE AFTER THE SALE. We stand behind our products 100% and we are in it for the long haul & to keep you, the customer happy.

        Why Buy From The Worldeyecam Security Store. 30 Day Money Back Guarantee Latest Product Version Guarantee Fast Accurate Same Day Shipping Friendly customer service.

        We are committed to providing our customers with "Complete Purchasing Experience Satisfaction" This means quality customer service from pre-purchase support, easy secure encrypted ordering, fast UPS shipping , comprehensive after sales tech-support by certified professionals and hassle free returns.

        Shipping Information
        FREE UPS Ground Shipping Continental US addresses on all orders over $1000.00 All in stock items are usually shipped Same Day (*not including weekends and holidays). For any Order for Bulk Cables that weigh over 75 lbs will be charged extra. Orders placed before 3 pm PST, or 2 pm for Expedited orders (Next Business Day Air or 2nd Business Day Air) can usually be shipped the same day. Orders placed by internet or by phone receive the same priority handling.

        We accept the following payment methods:

        Accepted payment methods


        Government PO Purchase Orders

        Guarantee SealOur Commitment

        EZ - Hassle FREE - Returns
        WorldEyeCam provides a 15-30-day money back guarantee on all products and services purchased, except special order items and all international orders. If for any reason you are not satisfied with your purchase, simply notify us by using this form here:

        Submit RMA Return Form *Click Here* and we will immediately issue a Return Material Authorization Number. 





        Shopper Award