WEC-PTZ30ATCIR 2MP 30x Optical Zoom IP PTZ Camera


Availability: In Stock
Ships Same Day
List Price: $2,499.00
Product #: 85032

Remote Login Support:

2 Megapixel, 30x Zoom, Sony Exmor Progressive Scan CMOS Image Sensor, Full HD Network Infrared PTZ Dome Camera

This HD pan/tilt/zoom surveillance camera records at 30 frames per second with a 1080p resolution. It has a 4.3-129mm lens with 30x optical zoom. Infrared LEDs allow the security camera to record up to a distance of 492 feet in darkness. The pan/tilt/zoom functions allow for a continuous 360 degree view. Users can view footage and operate controls remotely from a PC or smart phone.


  • Intelligent Infrared PTZ
  • Texas Instruments DaVinci DSP
  • 2MP Progressive Scan Sony Exmor CMOS Sensor
  • 30x Optical Zoom
  • Max 30fps @ 1080p
  • H.264 & MJPEG Dual-Stream Encoding
  • IR Distance up to 150m
  • ONVIF Profile S
  • IP66 Ingress Protection


Auto-Tracking IP-Pan Tilt Zoom Camera



Sensor Type

2MP 1/3” Sony Exmor CMOS

Digital Signal Processor

Ti DaVinci

Lens Type

4.3 ~ 129mm (30x Optical Zoom)

Effective Pixels

1920 (H) x 1080 (V), 2 Megapixels

Minimum Illumination

Color: 0.05Lux@F1.6, B&W: 0.005Lux@F1.6

Digital Zoom


Electronic Shutter Speed

1/3 ~ 1/30,000s

White Balance

Auto / ATW / Indoor / Outdoor / Manual


Auto (ICR) / Color / B&W

Backlight Compensation

BLC / HLC / DWDR (Digital WDR)

S/N Ratio


Privacy Masking

Up to 24 areas

Video Compression

H.264 / MJPEG

Image Resolution

1080p (1920/1080) / 720p ( 1280/720) / D1 (704x480) / CIF (352 x 240)

Frame Rate: Main Stream

1080p (1 ~ 30fps) / 720p (1 ~ 60fps)

Frame Rate: Extra Stream

D1 / CIF (1 ~ 30fps)

Bit Rate

56 - 8192Kbps

Audio Compression

G.711a / G.711u / PCM




RJ-45 (10/100Mbps)



ONVIF Compliance

ONVIF Profile S

Maximum Concurrent Users


Remote Access

Web Interface, CMS (PSS), Smartphone (iMaxCam)

Speed Dome


Pan/Tilt Range

Pan: 0° - 360° continuous; Tilt: -10° - 90°, auto-flip 180°

Manual Speed

Pan: 0.1° ~ 200° / second; Tilt: 0.1° ~ 120° / second

Preset Speed

Pan: 240° / second; Tilt: 200° / second

PTZ Mode

5 Pattern / 8 Tour / Auto Pan / Auto Scan

Alarm I/O

7 / 2 relay Input / Output

Idle Motion

Activate Preset / Pan / Scan / Tour / Pattern

IR Distance


Memory Slot

Micro SD, Max 64GB



Power Requirements

AC 24V/3A

Power Consumption

20W / 43W (IR on, Heater on)

Environmental & Physical


Operating Temperature

-40° F ~ +140° F

Operating Humidity

0-90% ( No condensation )

Ingress Protection


PTZ Weight


Shipping Weight


IR Speed Dome Manual
Speed Dome Manual
Auto-Tracking Quick Guide

Average Customer Rating:

1 Most useful customer reviews
Rich Drees
Nov 10, 2015
This customer purchased the item at our site.
My brother purchased a similar camera to this from this website 2 months ago and has not had a bad word to say about it. It runs smoothly, no glitches, has the clearest quality photos and videos and best of all he can view all his footage remotely from his iPhone. I was really flabbergasted by this feature for my current security camera can only be viewed via my desktop PC. I browsed through this site for some time before finding this 30 x optical zoom camera. Not just that but this camera can videotape all activity that is happening at night (in complete darkness) at a distance of 492 feet. Guess I hit the jackpot with this one!

Another feature that had me mesmerized was the infrared LEDs. Always I see security cameras with the LEDS positioned on the lens of the camera but this one has a completely different compartment for that. Totally recommend this product for everyone out there. Cheers!
Loading...Was the above review useful to you? Yes (0) / No (0)

Mobile APPs

QR Code Scan P2P iPhone Android iOS instructions

How to enable remote viewing without Port-Forwarding

We offer our own WorldEyeCam mobile apps for iPhone, iPad, Android phones and tablets. Our mobile apps allow you to remotely view your DVR and cameras from anywhere on the world. In this guide we will show you how to setup P2P or QR Code Scanning setup. No Port-Forwarding Needed.

Easy remote Viewing
P2P/QR Code Easy Setup

To access the P2P or QR code screen, you must first power on your recorder. Right click and select Main Menu->Setup->Network->P2P and the P2P/QR code will display.

You must check the box to enable P2P function and then click Apply to save at bottom of screen.


Make sure that your NVR/DVR is connected to your modem/router with a CAT5/Ethernet cable. Once P2P has been enabled please go to TCP/IP section inside of the network screen. Enable “DHCP” inside of the Network settings and save. Once DHCP has been enabled you will need to reboot the system.


Upon rebooting navigate back to the P2P setting to the system and scan the code with your mobile iMaxCam app and from this point you should be able to see the cameras.



How to setup the iPhone app with the P2P/QR Code

Step 1: Open the iMaxCam app and tap on Camera.

Step 2: Tap the menu icon on the top left corner to access the menu as shown in the picture.

Step 3: Tap the DEVICE MANAGER option to enter your DVR/NVR login information

Step 4: Once in device manager tap the plus sign button (+), in the top right corner to advance to the next screen.

Step 5: In the add device screen, select P2P

Step 6: In this Screen you need to tap the QR code icon on the right where the S/N field is.

Once you tap on QR Code icon the camera of your phone will start, go ahead and scan the code.

Name: DVR

S/N: Tap on the icon to scan the QR Code

User Name: admin (default)

Password: admin (default)

Step 7: Press the “Start Live Preview” button to start watching the cameras.

Viewing the live camera feed from your Integrator Series Network Video Recorder, or NVR, through a mobile device is simple, and can be done in less than five minutes. If you have used our G4MX App you will find it’s very similar, but if you haven’t, that’s okay too. As in the tutorial for iMaxCam, In this short tutorial we’ll be showing you how to setup your live security camera feed on your mobile device via the peer-to-peer, or P2P method, using a QR Code Scanning setup. Think of it as allowing your camera server and your mobile device to meet up and communicate together in the cloud, just by using a bar code your device can read. No Port-Forwarding or IT specialists needed. On your NVR, rick click to login to the main menu. Then select “System”, then “Network”, then click the box marked “Enable DHCP”. This should allow all the forms to be automatic when you connect your device. If you would rather set your IP address manually, you can do that as well. Just leave the “Enable DHCP” box unchecked and you will be given an opportunity to set your IP address yourself. In the setting page you’ll see the QR code. Leave that up on your screen, because you will need to scan it with your mobile momentarily. On your mobile device, download the “EZView” App from your preferred app store. Once downloaded, go ahead and open “EZView”. Select the main menu icon in the top left hand corner. Then select “Devices”. This is where you can add new devices and manage existing ones. Now that you have your device page open, you will need to add a new device. To do this, select the “+“ in the top right corner. Select “Add By P2P” to change the registration mode. Be sure to name your device (any name that works for you), then tap on the QR code icon to scan the QR code displayed on your monitor. Once you’ve done this, all of the information for your NVR should appear on your mobile, with exception of your user name and password. Go ahead and enter your login details there if prompted. After Inputting the information above select “Start Live View” at the bottom of the page to complete the setup and begin viewing your camera’s live feed! If you have any other issues or need further assistance, don’t hesitate to contact us via phone, email, or live chat. We’re here to help you. Because at World Eye Cam, we’re not just about security cameras. We want you to feel secure.