Our All-Weather Elite (AWE) speakers offer great sound in a unique, yet ultra-stylish, design. The sound quality and appearance of these speakers make them invaluable for use in both indoor applications (such as bars, restaurants, schools, retail, etc.), and outdoor applications (such as homes, restaurants, schools, etc.).
ACM4CB converts one (1) 12 to 24 volt AC or DC input into four (4) independently controlled Class 2 Rated Power Limited PTC protected outputs. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. Unit is designed to be powered by one common power source which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the four (4) outputs.
The Video Ground Loop Isolator GLI-BNCPJPT-1 is a necessary part of every CCTV set-up, providing improved security from troublesome ground loop distortion. Installation of the Video Ground Loop Isolator rescues you from the irritation of tearing apart your set-up as you search for the source of irritating signal disturbances such as those caused by wiring laid too near power lines. The product also provides for better surge protection, while conveinience of installation means the Video Ground Loop Isolator is easily added to previously existing operation.
The GEC-VIT from GE Security is a Hi-Res Coax Video Isolation Transformer. The GEC-VIT is a high-resolution video isolation transformer designed for base-band composite video signals. Designed to ensure high-quality images, this transformer helps eliminate potentially damaging onscreen “hum bars” caused by ground voltage potential differences between your video equipment, also known as ground loop. The GEC-VIT provides complete isolation between devices and eliminates distortions caused by video hum bars, ground loops, and DC offsets. In addition, flat frequency and linear phase response provides excellent picture quality and the unit’s wide bandwidth is compatible with a large range of video formats without adding distortion.
Power Supply 16Ptc 6-15Vdc @ 4A Small Enclosure Line Cord, Type CCTV DC, Wall Mount, Material Steel, Finish Gray, Enclosure Depth 3.75 In, Enclosure Width 7.50 In, Enclosure Height 8.50 In, Input Voltage 115VAC, Voltage OUTPut 6-15VDC, OUTPut Current 4A Amps, Input Frequency 60 Hz, Standards UL 2044 Commercial CCTV, CUL, CE, Includes Battery Leads, Cam Lock
120V and 208/240V Receptacle Box for use with ED6200RM UPS control unit, EDBP6000RM external battery pack and ED6000RMXFRM transformer module combination. The ED6-120RB receptacle box can only be used in conjunction with the ED6000RMXFRM.
The IS1800HG Medical Grade Isolation Transformer offers line isolation and continuous noise filtering
Internal low-impedance isolation transformer with Faraday shield offers 100% isolation from the input AC line
UL60601-1 medical-grade listing with hospital-grade plug and outlet
receptacles makes Isolator Hospital Grade transformers ideal for the
protection of sensitive electronic equipment in patient-care areas.
the cumulative leakage current of the Isolator and connected equipment
to levels less than 100 microamps. Secondary neutral to ground bonding
eliminates common mode noise, providing an isolated ground reference for
Serves as an inexpensive alternative to dedicated circuits and site electrical upgrades
The IFS EtherNav™ D7600 series of Managed Ethernet Switches provide robust transmission of 10/100 BASE-T Ethernet data. Unlike most Ethernet switches, these environmentally hardened units are designed for direct deployment in difficult out-of-plant or roadside operating environments, and are available for use with either conventional CAT-5e copper or optical transmission media. Depending upon the configuration ordered, up to 9 electrical or 6 electrical and 3 optical ports are available for easily implementing point-to-point, linear add-drop/ drop-and-repeat, star, or true self-healing ring and mesh network system architectures. The electrical ports support the 10/100 Mbps (10/100 BASE-T) Ethernet IEEE 802.3 protocol, and autonegotiating and auto-MDI/MDIX features are provided for simplicity and ease of installation. A 1000 BASE-T or 1000 BASE-FX port (specified at time of order) is optionally available for optically or electrically linking D7600 series switches when additional IP communications ports are required, allowing simple and cost-effective future expansion of the network if required. Available for use with multimode or single mode optical fiber, these network managed (through SNMP), Layer 2 switches are optically (100 BASE-FX) and electrically compatible with any IEEE 802.3 compliant Ethernet device. Plug-and-play design ensures ease of installation, and no electrical or optical adjustments are ever required. LED indicators are provided for rapidly ascertaining the operating status of the managed switch and network, and these units are available in stand-alone/shelf-mount,wall-mount, rack-mount or DIN-rail mounting configurations.